Sondes de qualité d'eau connecté à enregistreur autonome et communicant

Data logger & physico-chemical probes


Available sensors :

  • Dissolved oxygen / Temperature : CAN-OX
  • Conductivity / Salinity / Temperature : CAN-CE
  • Inductive Conductivity / Salinity / Temperature : CAN-CZ
  • pH / ORP / Temperature  : CAN-PH
  • ORP potential / Temperature : CAN-ORP
  • Turbidity NTU-mg / l / Temperature : CAN-TU

Digital technology for optimized measurement
The all in one solution multi-parameters : data logger, physico-chemical probes, GSM / GPRS

– Integrated GSM for remote monitoring or on-site data retrieval by radio
– Data logger 400,000 measurments
– Quick and easy installation
– Reduced maintenance
– Battery pack available
– Battery life power > 5 years: a measurement / 15 min and 1 sending GSM / day
– Calibration on-site simplified

Digital physicochemical Technologies

liste_arrow DISOLVED OXYGEN / TEMPERATURE : Optical technology based on luminescent optical technology. This sensor is approved by the ASTM International Method D888-05. Accurate measures in all situations and especially in very low oxygen concentrations. Body in Stainless steel or TITANIUM.

liste_arrow PH / ORP / TEMPERATURE : Digital technology, combined electrodes, calibration data inside the sensor.

liste_arrow CONDUCTIVITY / SALINITY / TEMPERATURE : The electrode works with a technology in 4 electrodes: an alterning current of constant-voltage is established between a primary’s pair of electrodes in graphite. The secondary’s electrodes in platinum allow of regulate the voltage imposed to primary’s electrodes to reflect of the fouling. The voltage measured between the primary’s electrodes is in function of the resistance of place and so, of the conductivity.

liste_arrow INDUCTIVE CONDUCTIVITY / SALINITY / TEMPERATURE : A ring-type coil is excited at fixed intervals and the response is retrieved on a second coil, which is linked to the excited coil. The connectivity between the coils (determined by the degree of conductivity) takes place via the conducting solution.

Wireless logger GSM/GPRS and digital water quality probes

liste_arrow TURBIDITY / TEMPERATURE : The measure principle is based on infra-red nephelometry / 850 nm. The sensor can be calibrated with a formazin standard solution. The NTU sensor integrates a low-cost optical technology, with a very few maintenance and no consumables.

liste_arrow ORP POTENTIAL / TEMPERATURE : The sensor incorporates a reference electrode, used for ORP measurements, such as Ag/AgCl in saturated KCl electrolyte plasticized “PLASTOGEL”®. The electrolyte communicates directly with the external environment without interposition of capillary or porous.


Data loggers with wireless communication

The sensors connect to the loggers LOGV3 series on its RS485 Modbus input. The communication on-site with the logger is done safely by radio, from the bank or boat. This allows you to connect, configure the sensor and retrieve data locally. Several water quality probes can be connected to the same loger using a Y-connector. An additional external battery pack (Lithium battery, or rechargeable lead battery) can also be added to the installation.


GSM/GPRS Communication

The loggers with integrated communication card send data via GSM / GPRS to the supervision or on Thresholds are configurable, as well as the frequency of sending the reports.


Typical areas of application :

  • Treatment of urban waste water
  • Treatment of industrial effluents
  • Natural water monitoring
  • Drinking water


Datalogger : 500.000 Measures
Concentrator : yes
Radio Antenna : Internal ou External HF Antenna depending on model
GSM Antenna : External on GSM/GPRS models
Options : Entrées Modbus RS485
Housing : ABS 20%FV
Operating temperature : -40 …85°C
Sealing : IP68
Énergy  : 3,6V 17 Ah à 34Ah
Autonomy : Up to 4 years
Programing : AVELOUR software using RFID wireless connection




You may also like…